Loading... Please wait...

12V Electronic Signal Flasher Module Relay w/ Ground Wire for LED

Your Price:
$11.85 (You save $6.10)

  • Image 1

2 pin LED Signal Flasher Module Relay w/ Ground!

This is a 12V electronic signal flasher (blinker) module relay that is a plug and play design.  This relay is designed to fix "no flash" or "hyper flash" problems that often result after installing LED bulbs as turn signal lights.  This is designed for vehicles with LED bulbs installed in the lights in some or all of the turn signals locations.  We caution the use of this in towing vehicles where a high number of incandescent bulbs in the vehicle and trailer are controlled by the vehicles turn signal system, as maximum the capacity of this unit is a 20A load.  Exceeding a 20A load will damage this unit.  If your vehicle does not have any LED bulbs in the turn signal circuit, you may also consider our 12V Electronic Signal Flasher Relay, which is designed for full incandescent or combination systems with mostly incandescent bulbs in the turn signal circuit.   

This flasher has a ground wire that allows the flasher to sequence even when the load would be invisible to other flashers.  Simply ground the wire to your chassis and plug the flasher into the stock flasher location.  There are no other modifications required to use this flasher in most vehicles.  These high quality electronic flashers are designed to replace standard two terminal flasher relays and operate at the normal DOT blink rate for motor vehicles with stock LED bulbs installed. If you are upgrading to LED turn signal lights, this is a must have item.

We only carry this in the common 2-pin design.  Please verify the correct flasher type for your vehicle before purchasing.  Some vehicles may require two flasher relays, one for the turn signals and one for the hazard lamps.

Write your own product review

Product Reviews

  1. 1968 Mustang LED turn signals and hazard flashers 4 Star Review

    Posted by on 11th Aug 2023

    Used two of these in a 1968 Mustang that was converted to all LED lighting. Flashers seem to work great for both purposes and were not too hard to install since I had instrument panel out for LED swap. A slight downgrade because the original flashers are round and these are rectangular. The hazard flasher does not fit well in the original clip in the car but it works. The original turn signal flasher had a little nub on the top that held it in the clip and this is missing from the replacement.

  2. I haven't used it yet 5 Star Review

    Posted by on 1st Mar 2022

    I'm just putting the dash back together and I was going to install this today but I noticed I have a 552 flasher in both locations so I have to find out which one is the turn signal (Normally a 224)

  3. Fixed my turn signal issues 5 Star Review

    Posted by on 30th Aug 2021

    I installed this in my vehicle to fix my turn signals not flashing. It did not work at first. Then The guys at HiPo told me to check the polarity of the wiring in my car that delivers the power to the flasher. It turns out my Mustang was wired backwards. I flipped the 2 wires around, reinstalled the flasher and my problem was solved. Non-flashing issue is GONE!!

  4. Electronic flasher 5 Star Review

    Posted by on 11th Nov 2020

    Flasher was easy to install, hardest part was to get a good ground close by as the ground wire is fairly short. Flasher works great and it makes a louder sound than a standard flasher. The audible noise tells you instantly that its working. Also installed 2nd one for E.Flashers. I ordered the led lights today hope they all work? Im confident it will work because I know Bill will take care of ANY problem that arises. Buy with confidence because Hipo will take care of you !!

  5. Flashed turn signals and hazards 5 Star Review

    Posted by on 22nd May 2020

    These relays enabled my sequential turn signals and hazard lights to flash properly after converting to LED turn signal bulbs.

  6. This flasher worked!!! 5 Star Review

    Posted by on 23rd Jul 2019

    I tried several flasher units and my indicators would not flash at all, they would just light up when operated. Installed this one and they flashed correctly - so I purchased two spare ones.